SWS-250 LBS 測力傳感器        SWS-250 LBS 測力傳感器       

 深圳市漢斯福特科技有限公司

：

: 3174269615

公司地址：龍華新區大浪街道大浪社區偉達工業園A棟2樓

公司：www.huntsort。。ｃｏｍ

SWS SERIES CAPACITY RANGES: 10, 20, 50, 100, 250, 600, 1,000 FT. LBS.

Our SWS Series reaction type socket wrench torque sensors are available in ranges from 10 ft-lbs. through 1000 ft-lbs. and provide accurate measurements of bolt or nut wrenching torques. These sensors are bi-directional so both tightening and break-away torques can be measured. These low cost sensors deliver high accuracy and outstanding frequency response. Calibration of mechanical torque wrenches may be performed with this sensor. The sensing element incorporates bonded foil strain gages of the highest quality.

參數

Rated Output (R.O.): 2 mV/V nominal

Nonlinearity: 0.2% of R.O.

Hysteresis: 0.2% of R.O.

Nonrepeatability: 0.1% of R.O.

Zero Balance: 1.0% of R.O.

Compensated Temp. Range: 60° to 160°F

Safe Temp. Range: -65° to 200°F

Temp. Effect on Output: 0.005% of Load/°F

Temp. Effect on Zero: 0.01% of R.O./°F

Terminal Resistance: 350 ohms nominal

Excitation Voltage: 10 VDC

Safe Overload: 150% of R.O.

訂貨型號

SWS-10 10 1/4 2.063 1.312 .375 .625

SWS-20 20 1/4 2.063 1.312 .375 .625

SWS-50 50 3/8 2.312 1.312 .500 .875

SWS-100 100 3/8 2.350 1.312 .500 .875

SWS-250 250 1/2 2.625 1.500 .688 1.125

SWS-600 600 3/4 3.938 2.000 1.063 1.625

SWS-1K 1,000 1.0 4.375 1.875 1.125 2.500

SWP稱重傳感器

SWP Series CAPACITY RANGES: 1,000, 2,000, 3,000, 5,000, 10,000, 20,000, 50,000 LBS.

Our SWP Series low profile load cells are an excellent choice for applications that require ultra stiffness and resistance to extraneous bending and side load forces.

For tension and/or compression applications, the load cell is bolted down to a flat surface and center loaded, utilizing the thru tapped hole. Load buttons or load bearing compression only applications are offered in our accessories section. For in line tension applications, we recommend our tension base (-TB option) for hardness, flatness, stiffness, and alignment. The SWP Series load cell and the –TB (tension base) are manufactured from heat treated 17-4ph stainless steel. The same high quality full bridge strain gage installation is utilized in all our force and torque measuring products.

參數

Rated Output (R.O.): 2 mV/V nominal

Nonlinearity: 0.05% of R.O.

Hysteresis: 0.05% of R.O

Nonrepeatability: 0.05% of R.O.

Zero Balance: 1.0% of R.O.

Compensated Temp. Range: 60° to 160°F

Safe Temp. Range: -65° to 200°F

Temp. Effect on Output: 0.005% of Load/°F

Temp. Effect on Zero: 0.005% of R.O./°F

Terminal Resistance: 700 ohms nominal

Excitation Voltage: 10-20 VDC

Safe Overload: 150% of R.O.

Deflection Inches: 0.001 inches @ R.O.

Fatigue Life One Direction: 100 x 1000000

Fatigue Life Bidirectional: 50 x 1000000

Calibration Included: Compression

Optional Calibration: Tension

訂貨型號

SWP-1K 1,000 lb Compression Included, Tension Optional

SWP-2K 2,000 lb Compression Included, Tension Optional

SWP-3K 3,000 lb Compression Included, Tension Optional

SWP-5K-4 5,000 lb Compression Included, Tension Optional

SWP-5K 5,000 lb Compression Included, Tension Optional

SWP-10K 10,000 lb Compression Included, Tension Optional

SWP-20K 20,000 lb Compression Included, Tension Optional

SWP-50K 50,000 lb Compression Included, Tension Optional

配件

TC-CAL N/A Tension Calibration Option

TC-CAL-1 N/A Tension Calibration Option 21,000-50,000 lb

CAL-TEDS N/A Plug & Play Option with Connector

TB0-SWP135 N/A Tension Base (1K-5K-4)

TB1-SWP1020 N/A Tension Base (5K-20K)

TB2-SWP50K N/A Tension Base (50K)