China PPS PTFE-hGR312 PPS描述：
PPS can be extruded or blow molded, may be used to produce films and composites, and is an excellent candidate for fuel cells and diesel fuel cars. China products have been specified in a wide range of injection molded applications such as automotive under-the-hood parts, power train components, pumps, fuel system components, surface mount electrical/electronics components, blower and pump parts, protective and non-stick coatings, surgical devices and power tools.
PPS
PPS is insoluble in all known solvents below 200°C （392° F）. It also shows tremendous stability in both typical and alternative automotive fuels. Standard injection moldable grades with glass fibers and/or mineral reinforcements are available, but many specialty grades are available for improved lubricity, low warpage, faster cycling and other areas of enhanced performance.Certain grades of PPS comply with ISO 10993 and USP Class VI, and Drug （DMF 14844） and Device （MAF-1097） Master Files have been created for them. These grades also meet European Directive 2002/72/EC for food contact applications and BfR （German Federal Institute for Risk Assessment , formerly BgVV, the German Federal Institute for Consumer Health Protection and Veterinary Medicine） standards.PPS is a high-temperature linear PPS that offers excellent dimensional stability, inherent flame resistance, and excellent chemical and solvent resistance.Aerospace Wing and Leading Edge Nose
PPS already had all the basic characteristics for use in aircraft construction – resistance to high temperatures and aggressive chemicals, hardness, impact strength, dimensional stability and inherent flame-retardancy. The trick was to create suitable structural elements embodying these attributes. This is done by extruding the PPS into film, combining it with chosen fibrous reinforcements and forming the final part under high pressure at 300°C （572°F）. Individual parts are then fabricated from the pressed composites and welded together in an autoclave to form the final component as one piece.Fiber-reinforced composites based on ’s high performance polyphenylene sulfide （PPS） make an important contribution to weight reduction of the Airbus A340 and A380. This helps lower fuel consumption and increase range and passenger capacity.
供水歧管
在英國，生活用水通常是從家庭規模的估計。然而，安裝設備允許國內水公司是由英國大西洋塑料水表的簡單連接。在與赫斯特工程聚合物事業部，英國，廣泛的有限元分析和模流研究合作制作了一個堅固的外殼，這些組件所提出的要求是相當可觀的。例如，外殼必須能承受50年的12酒吧的壓力，并有相應的高蠕變和疲勞強度。在自來水的其他成型也從泰科納聚合物制成。 切斷桿和連接器組成的玻璃纖維增強，由于其高強度和剛度。，確保*順利運作。zui后，保留夾具，受到*的機械載荷，40％玻璃纖維增強聚苯硫醚注塑成型。特點：優化優異的耐久性，在某些情況下，防滑性能，即使在高負荷。產品圖片
東莞市龍輝祥塑膠原料公司是一家專業從事塑膠原料進口貿易公司。主營各國通用塑膠、工程塑膠、特種工程塑膠。公司以“誠信為本，創新求魂”的精神在客戶中樹立了良好的口碑。從進口到出口嚴格把關，可提供COA,SGS,UL黃卡!保證原廠原包!我是龍輝祥，期待你的來電!
電 話：
傳 真：
手 機：
：羅（業務）
:羅長龍
:
傳真號碼:
地址:中國廣東東莞市樟木頭鎮塑膠原料市場
銷售China PPS PTFE-hGR312 PPS其它產品
銷售Zy 70G25HSLR NC010
銷售Zy 70G25HSLR BK099
銷售China PPS PTFE-hGR303 PPS
銷售Zy 70G13L NC010
銷售China PPS PTFE-hGR302 PPS
銷售Zy 70G13HS1L NC010
銷售Zy 70G13HS1L BK031
銷售China PPS PTFE-hGR203 PPS
銷售Zy 132F NC010
