美國Transducer Techniques SWS-50LBS 測力傳感器
美國Transducer Techniques SWS-50LBS 測力傳感器
美國Transducer Techniques SWS-50LBS 測力傳感器
SWS SERIES CAPACITY RANGES: 10, 20, 50, 100, 250, 600, 1,000 FT. LBS.
Our SWS Series reaction type socket wrench torque sensors are available in ranges from 10 ft-lbs. through 1000 ft-lbs. and provide accurate measurements of bolt or nut wrenching torques. These sensors are bi-directional so both tightening and break-away torques can be measured. These low cost sensors deliver high accuracy and outstanding frequency response. Calibration of mechanical torque wrenches may be performed with this sensor. The sensing element incorporates bonded foil strain gages of the highest quality.
參數
Rated Output (R.O.): 2 mV/V nominal
Nonlinearity: 0.2% of R.O.
Hysteresis: 0.2% of R.O.
Nonrepeatability: 0.1% of R.O.
Zero Balance: 1.0% of R.O.
Compensated Temp. Range: 60° to 160°F
Safe Temp. Range: -65° to 200°F
Temp. Effect on Output: 0.005% of Load/°F
Temp. Effect on Zero: 0.01% of R.O./°F
Terminal Resistance: 350 ohms nominal
Excitation Voltage: 10 VDC
Safe Overload: 150% of R.O.
訂貨型號
SWS-10 10 1/4 2.063 1.312 .375 .625
SWS-20 20 1/4 2.063 1.312 .375 .625
SWS-50 50 3/8 2.312 1.312 .500 .875
SWS-100 100 3/8 2.350 1.312 .500 .875
SWS-250 250 1/2 2.625 1.500 .688 1.125
SWS-600 600 3/4 3.938 2.000 1.063 1.625
SWS-1K 1,000 1.0 4.375 1.875 1.125 2.500
SWP稱重傳感器
SWP Series CAPACITY RANGES: 1,000, 2,000, 3,000, 5,000, 10,000, 20,000, 50,000 LBS.
Our SWP Series low profile load cells are an excellent choice for applications that require ultra stiffness and resistance to extraneous bending and side load forces.
For tension and/or compression applications, the load cell is bolted down to a flat surface and center loaded, utilizing the thru tapped hole. Load buttons or load bearing compression only applications are offered in our accessories section. For in line tension applications, we recommend our tension base (-TB option) for hardness, flatness, stiffness, and alignment. The SWP Series load cell and the –TB (tension base) are manufactured from heat treated 17-4ph stainless steel. The same high quality full bridge strain gage installation is utilized in all our force and torque measuring products.
參數
Rated Output (R.O.): 2 mV/V nominal
Nonlinearity: 0.05% of R.O.
Hysteresis: 0.05% of R.O
Nonrepeatability: 0.05% of R.O.
Zero Balance: 1.0% of R.O.
Compensated Temp. Range: 60° to 160°F
Safe Temp. Range: -65° to 200°F
Temp. Effect on Output: 0.005% of Load/°F
Temp. Effect on Zero: 0.005% of R.O./°F
Terminal Resistance: 700 ohms nominal
Excitation Voltage: 10-20 VDC
Safe Overload: 150% of R.O.
Deflection Inches: 0.001 inches @ R.O.
Fatigue Life One Direction: 100 x 1000000
Fatigue Life Bidirectional: 50 x 1000000
Calibration Included: Compression
Optional Calibration: Tension
訂貨型號
SWP-1K 1,000 lb Compression Included, Tension Optional
SWP-2K 2,000 lb Compression Included, Tension Optional
SWP-3K 3,000 lb Compression Included, Tension Optional
SWP-5K-4 5,000 lb Compression Included, Tension Optional
SWP-5K 5,000 lb Compression Included, Tension Optional
SWP-10K 10,000 lb Compression Included, Tension Optional
SWP-20K 20,000 lb Compression Included, Tension Optional
SWP-50K 50,000 lb Compression Included, Tension Optional
配件
TC-CAL N/A Tension Calibration Option
TC-CAL-1 N/A Tension Calibration Option 21,000-50,000 lb
CAL-TEDS N/A Plug & Play Option with Connector
TB0-SWP135 N/A Tension Base (1K-5K-4)
TB1-SWP1020 N/A Tension Base (5K-20K)
TB2-SWP50K N/A Tension Base (50K)
