代 號 PART NO. | 螺 紋 THREAD | 管子外徑 TUBE O.D. | 尺 寸 DIMENSIONS | 壓力等級 MPa | |||||
E | F | D1 | B | l1 | L1 | S1 | S2 | ||
1CG-12-02 | M12X1.5 | G1/8"X28 | 6 | 9.5 | 8.5 | 23 | 14 | 14 | 31.5 輕系列 L |
1CG-12-04 | M12X1.5 | G1/4"X19 | 6 | 10 | 10 | 25 | 19 | 14 | |
1CG-14-04 | M14x1.5 | G1/4"X19 | 8 | 10 | 10 | 25 | 19 | 17 | |
1CG-14-06 | M14x1.5 | G3/8"X19 | 8 | 11.5 | 11.5 | 26 | 22 | 17 | |
1CG-14-08 | M14x1.5 | G1/2"X14 | 8 | 14 | 13 | 27.5 | 27 | 34 | |
1CG-16-04 | M16x1.5 | G1/4"X19 | 10 | 10 | 11 | 26 | 19 | 19 | |
1CG-16-06 | M16x1.5 | G3/8"X19 | 10 | 11.5 | 12.5 | 27 | 22 | 19 | |
1CG-16-08 | M16x1.5 | G1/2"X14 | 10 | 14 | 14 | 29 | 27 | 19 | |
1CG-18-06 | M18x1.5 | G3/8"X19 | 12 | 11.5 | 12.5 | 27 | 22 | 22 | |
1CG-18-08 | M18x1.5 | G1/2"X14 | 12 | 14 | 13 | 28 | 27 | 22 | |
1CG-22-06 | M22x1.5 | G3/8"X19 | 15 | 11.5 | 13.5 | 29 | 24 | 27 | |
1CG-22-08 | M22x1.5 | G1/2"X14 | 15 | 14 | 14 | 29 | 27 | 27 | |
1CG-22-12 | M22x1.5 | G3/4"X14 | 15 | 15.5 | 20 | 30 | 32 | 32 | |
1CG-26-08 | M26x1.5 | G1/2"X14 | 18 | 14 | 14.5 | 31 | 27 | 32 | |
1CG-26-12 | M26x1.5 | G3/4"X14 | 18 | 15.5 | 14.5 | 32 | 32 | 32 | |
1CG-30-12 | M30x2 | G3/4"X14 | 22 | 15.5 | 16.5 | 33 | 32 | 36 | 16 輕系列 L |
1CG-30-16 | M30x2 | G1"X11 | 22 | 18 | 17.5 | 35 | 41 | 36 | |
1CG-36-16 | M36x2 | G1"X11 | 28 | 18 | 17.5 | 34 | 41 | 41 | |
1CG-45-20 | M45x2 | G1.1/4"X11 | 35 | 20 | 17.5 | 39 | 50 | 50 | |
1CG-52-20 | M52X2 | G1.1/4"X11 | 42 | 20 | 19 | 42 | 55 | 60 | |
1CG-52-24 | M52x2 | G1.1/2"X11 | 42 | 21.5 | 19 | 42 | 55 | 60 | |
1CG-52-32 | M52x2 | G2"X11 | 42 | 24.5 | 25 | 44 | 70 | 60 | |
1DG-14-04 | M14X1.5 | G1/4"X19 | 6 | 10 | 13 | 28 | 19 | 17 | 63 重系列 S |
1DG-16-04 | M16X1.5 | G1/4"X19 | 8 | 10 | 15 | 31 | 19 | 19 | |
1DG-18-04 | M18x1.5 | G1/4"X19 | 10 | 10 | 14.5 | 31 | 19 | 22 | |
1DG-18-06 | M18x1.5 | G3/8"X19 | 10 | 11.5 | 15 | 31 | 22 | 22 | |
1DG-20-06 | M20x1.5 | G3/8"X19 | 12 | 11.5 | 17 | 32 | 22 | 24 | |
1DG-20-08 | M20x1.5 | G1/2"X14 | 12 | 14 | 17.5 | 34 | 27 | 24 | |
1DG-22-06 | M22x1.5 | G3/8"X19 | 14 | 11.5 | 19 | 37 | 24 | 27 | |
1DG-22-08 | M22x1.5 | G1/2"X14 | 14 | 14 | 19 | 37 | 27 | 27 | |
1DG-24-04 | M24x1.5 | G1/4"X19 | 16 | 11 | 18 | 37 | 27 | 30 | |
1DG-24-08 | M24x1.5 | G1/2"X14 | 16 | 14 | 18.5 | 37 | 27 | 30 | 40 重系列 S |
1DG-30-12 | M30x2 | G3/4"X14 | 20 | 15.5 | 20.5 | 42 | 32 | 36 | |
1DG-36-12 | M36x2 | G3/4"X14 | 25 | 15.5 | 23 | 47 | 41 | 46 | |
1DG-36-16 | M36x2 | G1"X11 | 25 | 18 | 17.5 | 47 | 41 | 46 | |
1DG-42-16 | M42x2 | G1"X11 | 30 | 18 | 23.5 | 48 | 46 | 50 | |
1DG-42-20 | M42x2 | G1.1/4"X11 | 30 | 20 | 23.5 | 50 | 50 | 50 | |
1DG-52-24 | M52x2 | G1.1/2"X11 | 38 | 21.5 | 26 | 57 | 55 | 60 | 31.5重系列S |
注:如需帶卡套及卡套螺母整套訂貨,則請在代號后加“RN”, 如 1DG-20-08RN。 Note:In case if you are interested to order the adapter in complete set with cutting ring and nut ,it is necessary to insert suffix "RN" after our part no.,for example 1DG-20-08RN. |
(1)按第9章要求對務必磷化處理的管子先要磷化處理處理;
(2)按務必長度用數控鋸床或專用激光切管機等設備斷掉管子,毫無疑問不允許用溶斷(如數控機床數控火焰切割)或沙輪片光纖激光切割;除去管子端尾內外圓毛刺、金屬復合材料鉆削及污垢;除去不銹鋼板材三通接頭的防銹劑及污垢;此外還要保證管子同軸度;
(3)將螺帽、卡套先后套入管子,卡套前端工程師傷口(小道端)距管子口至少2毫米,接著將管子插到不銹鋼接頭人體錐孔,抵到才行;
(4)慢慢地扭緊螺帽,此外轉動管子直至不動時,再扭緊螺帽2/3~4/3圈;
(5)拆裝檢查卡套是否已挑選管子,位置是否適當。不銹鋼接頭卡套不允許有軸向移動,可稍有轉動;
(6)三通式管接頭檢查合格后再度扭緊不銹鋼接頭螺帽。