代 號 PART NO. | 螺 紋 THREAD | 管子外徑TUBE O.D. | 尺 寸 DIMENSIONS | |||||
E | F | D1 | A | B | B | S1 | S2 | |
2CB-12-02 | M12X1.5 | G1/8"X28 | 6 | 11 | 5.5 | 26 | 14 | 14 |
2CB-14-04 | M14X1.5 | G1/4"X19 | 8 | 13 | 5.5 | 30.5 | 17 | 19 |
2CB-16-04 | M16X1.5 | G1/4"X19 | 10 | 13.5 | 5.5 | 30.5 | 17 | 19 |
2CB-16-06 | M16X1.5 | G3/8"X19 | 10 | 13.5 | 6.3 | 32 | 17 | 22 |
2CB-16-08 | M16X1.5 | G1/2"X14 | 10 | 13.5 | 7.5 | 33.5 | 19 | 27 |
2CB-18-06 | M18X1.5 | G3/8"X19 | 12 | 13.5 | 6.3 | 32 | 19 | 22 |
2CB-22-06 | M22X1.5 | G3/8"X19 | 15 | 13.5 | 6.3 | 33.5 | 24 | 22 |
2CB-22-08 | M22X1.5 | G1/2"X14 | 15 | 13.5 | 7.5 | 35.5 | 24 | 27 |
2CB-26-08 | M26X1.5 | G1/2"X14 | 18 | 14 | 7.5 | 38 | 27 | 27 |
2CB-30-12 | M30X2 | G3/4"X14 | 22 | 18 | 10.9 | 44 | 32 | 32 |
2CB-36-12 | M36X2 | G3/4"X14 | 28 | 18 | 10.9 | 44 | 38 | 32 |
2CB-36-16 | M36X2 | G1"X11 | 28 | 18 | 11.7 | 45 | 38 | 41 |
2CB-45-20 | M45X2 | G1.1/4"X11 | 35 | 19 | 11 | 50.5 | 46 | 50 |
2CB-52-24 | M52X2 | G1.1/2"X11 | 42 | 19 | 13 | 53 | 55 | 55 |
(1)按照規定對務必磷化處理的管子先要磷化處理處理;
(2)按務必長度用數控鋸床或專用激光切管機等設備斷掉管子,毫無疑問不允許用溶斷(如數控機床數控火焰切割)或沙輪片光纖激光切割;除去管子端尾內外圓毛刺、金屬復合材料鉆削及污垢;除去不銹鋼板材連接頭的防銹劑及污垢;此外還要保證管子同軸度;
(3)將螺帽、卡套先后套入管子,卡套前端工程師傷口(小道端)距管子口至少3mm,接著將管子插到不銹鋼接頭人體錐孔,抵到才行;
(4)慢慢地扭緊螺帽,此外轉動管子直至不動時,再扭緊螺帽2/3~4/3圈;
(5)拆裝檢查卡套是否已挑選管子,位置是否適當。不銹鋼接頭卡套不允許有軸向移動,可稍有轉動;
(6)檢查合格后再度扭緊不銹鋼接頭螺帽。"